ENXIA Technology

The generation architecture.

ENXIA Technology is a compact electromagnetic module deployed as distributed, 24×7 plants at industrial and data-center loads — power generated next to the place that uses it, non-stop, so it does not have to travel the grid and does not stop with the weather.

One ENXIA Technology modular unit

What ENXIA Technology is

A stackable unit that replaces mechanical rotation with digital switching.

ENXIA’s technology introduction describes a patented structure: no physical rotation. The same electromotive force that a rotary machine produces by alternating N and S poles is generated by AI-driven digital power switching — on the order of 120 on/off cycles per second — acting on an electromagnetic assembly.

  • One module is approximately the size of a single solar panel.
  • Charge and discharge units and supercapacitors regulate output.
  • AI software and hardware control the electromagnetic modulation cycles.
  • Remote, scenario-based control can be set for the offtaker.
  • Commercialization followed validation of the research prototype.

Our solution

Five attributes of the commercial module.

Plug & play

Operates immediately on connection. Zero loading time.

Non-rotary

Safe static structure. No turbine, no shaft, no mechanical rotation.

AI control

Hardware and software set output phase to the consumer’s requirement.

No combustion

No stack fuel and no combustion emissions. The rated input is electrical excitation and control current.

> 60 years

No mechanical wear. Specified service life exceeding sixty years.

Capacity factor above 95% is an ENXIA Technology operating specification in the September 2026 introduction. The same introduction lists a startup-energy multiple greater than 5× — that is not a heat-engine efficiency percentage, and this site does not present it as over-unity or perpetual motion. Capital cost per kilowatt is currently comparable to nuclear because it is calculated from the experimental prototype. Volume production may reduce unit cost; that reduction is not stated here as today’s price. Levelized cost of electricity (LCOE) is described as comparably lower, and that figure is still to be confirmed.

ENXIA Technology electromagnetic coil field and laboratory imaging

Working principle

Faraday induction without a spinning rotor.

Conventional hydro, wind, thermal, and nuclear plants create alternating N and S magnetic poles by driving a mechanical rotor. ENXIA Technology keeps the electromagnetic induction path — electricity to magnetism, magnetism to electricity — and replaces the rotor with a remanence activation loop: a short excitation pulse, a remnant field, then a sustained generation phase under digital control.

The rated electrical input is a 13 A control current, held from one module to a 30-module string, plus the excitation pulse that starts the loop. Coil fields add as units are paralleled; output is specified to grow in arithmetic progression. That is the scaling rule ENXIA uses to design U.S. plants. Independent energy-balance publication is not posted on this site.

ENXIA Technology industrial demonstration and meter readings

Test record

Industrial model, KEPCO measurement, KOLAS reports.

The introduction records industrial-model demonstrations with live input/output metering, input-battery measurement, and verification support from Korea Electric Power Corporation. KOLAS-accredited test reports from KES and instrument calibration certificates from Korea Calab are cited as the laboratory backbone. Document numbers and PDFs are not published on this site; the laboratory pack is available from ENXIA on request.

  • KOLAS and KES test reports are cited, not posted as public files.
  • KEPCO measurement support is cited. The pack is available on request.
  • The patent estate cites 159+ countries and 200+ filings. The numbers are available on request.
  • This page does not replace an independent energy-balance study.

From module to plant

ENXIA Technology. Off-grid plants.

ENXIA Technology has been presented at WFES Abu Dhabi, a Seoul international demonstration, and COP28. ENXIA turns those modules into off-grid plants for U.S. industry and data centers.

2015–2018

Research

SEG research begins. Korean and PCT filings for the electromagnetic architecture.

2019–2023

Demonstration

WFES, KEPCO/KOLAS measurement, Seoul demonstration, COP28 launch.

2026

Off-grid U.S.

ENXIA Technology is deployed as off-grid generation for industry and data centers.

See off-grid plants